ASTM G63-99

    Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF 26 $74.40   ADD TO CART


    1. Scope

    1.1 This guide applies to nonmetallic materials, (hereinafter called materials) under consideration for oxygen or oxygen-enriched fluid service, direct or indirect, as defined below. It is intended for use in selecting materials for applications in connection with the production, storage, transportation, distribution, or use of oxygen. It is concerned primarily with the properties of a material associated with its relative susceptibility to ignition and propagation of combustion; it does not involve mechanical properties, potential toxicity, outgassing, reactions between various materials in the system, functional reliability, or performance characteristics such as aging, shredding, or sloughing of particles, except when these might contribute to an ignition.

    1.2 When this document was originally published in 1980, it addressed both metals and nonmetals. Its scope has been narrowed to address only nonmetals and a separate standard Guide G94 has been developed to address metals.

    1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use .

    Note 1-The American Society for Testing and Materials takes no position respecting the validity of any evaluation methods asserted in connection with any item mentioned in this guide. Users of this guide are expressly advised that determination of the validity of any such evaluation methods and data and the risk of use of such evaluation methods and data are entirely their own responsibility. Note 2-In evaluating materials, any mixture with oxygen exceeding atmospheric concentration at pressures higher than atmospheric should be evaluated from the hazard point of view for possible significant increase in material combustibility.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Other Standard

    BS3N:100:1985 Specification for General Design Requirements for Aircraft Oxygen Systems and Equipment Available from British Standards Institute (BSI), 389 Chiswick High Rd., London W4 4AL, U.K., http://www.bsi-global.com.

    ASTM Standards

    D217 Test Methods for Cone Penetration of Lubricating Grease

    D566 Test Method for Dropping Point of Lubricating Grease

    D1264 Test Method for Determining the Water Washout Characteristics of Lubricating Greases

    D1743 Test Method for Determining Corrosion Preventive Properties of Lubricating Greases

    D1748 Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet

    D2512 Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques)

    D2863 Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

    D4809 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)

    G72 Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment

    G74 Test Method for Ignition Sensitivity of Materials to Gaseous Fluid Impact

    G86 Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments

    G88 Guide for Designing Systems for Oxygen Service

    G93 Practice for Cleaning Methods and Cleanliness Levels for Material and Equipment Used in Oxygen-Enriched Environments

    G94 Guide for Evaluating Metals for Oxygen Service


    ICS Code

    ICS Number Code 19.040 (Environmental testing)

    UNSPSC Code

    UNSPSC Code 12141904(Oxygen O)


    DOI: 10.1520/G0063-99

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top