ASTM G154-06

    Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

      Format Pages Price  
    PDF 11 $58.80   ADD TO CART

    1. Scope

    1.1 This practice covers the basic principles and operating procedures for using fluorescent UV light, and water apparatus intended to reproduce the weathering effects that occur when materials are exposed to sunlight (either direct or through window glass) and moisture as rain or dew in actual usage. This practice is limited to the procedures for obtaining, measuring, and controlling conditions of exposure. A number of exposure procedures are listed in an appendix; however, this practice does not specify the exposure conditions best suited for the material to be tested.

    Note 1

    Practice G 151 describes performance criteria for all exposure devices that use laboratory light sources. This practice replaces Practice G 53, which describes very specific designs for devices used for fluorescent UV exposures. The apparatus described in Practice G 53 is covered by this practice.

    1.2 Test specimens are exposed to fluorescent UV light under controlled environmental conditions. Different types of fluorescent UV light sources are described.

    1.3 Specimen preparation and evaluation of the results are covered in ASTM methods or specifications for specific materials. General guidance is given in Practice G 151 and ISO 4892-1. More specific information about methods for determining the change in properties after exposure and reporting these results is described in ISO 4582.

    1.4 The values stated in SI units are to be regarded as the standard.

    This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.5 This standard is technically similar to ISO 4892-3 and ISO DIS 11507.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D3980 Practice for Interlaboratory Testing of Paint and Related Materials

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    G53 Practice for Operating Light-and Water-Exposure Apparatus (Fluorescent UV-Condensation Type) for Exposure of Nonmetallic Materials

    G113 Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials

    G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources

    CIE Standard

    CIE-Publ.No.85:  Recommendations for the Integrated Irradiance and the Spectral Distribution of Simulated Solar Radiation for Testing Purposes Available from Secretary, U.S. National Committee, CIE, National Institute of Standards and Technology (NIST), Gaithersburg, MD 20899.

    ISO Standards

    ISO 4582 Plastics--Determination of the Changes of Colour and Variations in Properties After Exposure to Daylight Under Glass, Natural Weathering or Artificial Light Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036,

    ISO 4892-1 Plastics--Methods of Exposure to Laboratory Light Sources, Part 1, Guidance

    ISO 4892-3 Plastics--Methods of Exposure to Laboratory Light Sources, Part 3, Fluorescent UV lamps

    ISODIS 11507 Paint and Varnishes--Exposure of Coatings to Artificial Weathering in Apparatus--Exposure to Fluorescent Ultraviolet and Condensation Apparatus

    ICS Code

    ICS Number Code 19.040 (Environmental testing)

    UNSPSC Code

    UNSPSC Code 39101605(Fluorescent lamps)

    Referencing This Standard

    DOI: 10.1520/G0154-06

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM G154-06, Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials, ASTM International, West Conshohocken, PA, 2006,

    Back to Top