Standard Historical Last Updated: Dec 31, 2010 Track Document
ASTM F1714-96(2002)

Standard Guide for Gravimetric Wear Assessment of Prosthetic Hip-Designs in Simulator Devices

Standard Guide for Gravimetric Wear Assessment of Prosthetic Hip-Designs in Simulator Devices F1714-96R02 ASTM|F1714-96R02|en-US Standard Guide for Gravimetric Wear Assessment of Prosthetic Hip-Designs in Simulator Devices Standard new BOS Vol. 13.01 Committee F04
$ 75.00 In stock

Significance and Use

This guide uses a weight-loss method of wear determination for the polymeric components used with hip-joint prostheses, using serum or demonstrated equivalent fluid for lubrication, and running under a dynamic load profile representative of the human hip-joint forces during walking (1,2).6 The basis for this weight-loss method for wear measurement was originally developed (3) for pin-on-disk wear studies (see Practice F 732) and has been extended to total hip replacements (4,5) and to femoral-tibial knee prostheses (6), and to femoropatellar knee prostheses (6,7).

While wear results in a change in the physical dimensions of the specimen, it is distinct from dimensional changes due to creep or plastic deformation, in that wear generally results in the removal of material in the form of polymeric debris particles, causing a loss in weight of the specimen.

This guide for measuring wear of the polymeric component is suitable for various simulator devices. These techniques can be used with metal, ceramic, carbon, polymeric, and composite counter faces bearing against a polymeric material (for example, polyethylene, polyacetal, and so forth). This weight-loss method, therefore, has universal application for wear studies of total-hip replacements that feature polymeric bearings. This weight-loss method has not been validated for high-density material bearing systems, such as metal-metal, carbon-carbon, or ceramic-ceramic. Progressive wear of such rigid bearing combinations generally has been monitored using a linear, variable-displacement transducers or by other profilometric techniques.

Scope

1.1 This guide describes a laboratory method using a weight-loss technique for evaluating the wear properties of materials or devices, or both, which are being considered for use as bearing surfaces of human-hip-joint replacement prostheses. The hip prostheses are evaluated in a device intended to simulate the terminological conditions encountered in the human hip joint, for example, use of a fluid such as bovine serum, or equivalent pseudosynovial fluid shown to simulate wear mechanisms and debris generation as found in vivo, and test frequencies of 1 Hz or less.

1.2 Since the hip simulator method permits the use of actual implant designs, materials, and physiological load/motion combinations, it can represent a more physiological simulation than basic wear-screening tests, such as pinion-disk (see Practice F 732) or ring-on-disk (see ISO-6474).

1.3 It is the intent of this guide to rank the combination of implant designs and materials with regard to material wear-rates under simulated physiological conditions. It must be recognized, however, that there are many possible variations in the in vivo conditions, a single laboratory simulation with a fixed set of parameters may not be universally representative.

1.4 The reference materials for the comparative evaluation of candidate materials, new devices, or components, or a combination thereof, shall be the wear rate of extruded or Compression-molded, ultra-high molecular weight (UHMW) polyethylene (see Specification F 648) bearing against standard counter faces Stainless Steel (see Specification F 138); cobalt-chromium-molybdenum alloy (see Specification F 75); thermomechanically processed cobalt chrome (see Specification F 799); alumina ceramic (see Specification F 603), having typical prosthetic quality, surface finish, and geometry similar to those with established clinical history. These reference materials will be tested under the same wear conditions as the candidate materials.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 13.01
Developed by Subcommittee: F04.22
Pages: 7
DOI: 10.1520/F1714-96R02
ICS Code: 11.040.40