ASTM D6394-03

    Historical Standard: ASTM D6394-03 Standard Specification for Sulfone Plastics (SP)

    SUPERSEDED (see Active link, below)


    Buy Standard (PDF)
    5 pages
    $50.40

    Active (view current version of standard)


    ASTM D6394

    1. Scope

    1.1 This specification covers the classification of sulfone plastics suitable for injection molding and extrusion.

    1.2 The properties included in this specification are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These will be specified by using the suffixes in Section 5.

    1.3 This specification is intended to be a means of calling out sulfone plastics used in the fabrication of end items or parts. Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, and the inherent properties of the material other than those covered by this specification.

    1.4 Sulfone polymers, being thermoplastic, are reprocessable and recyclable. This specification allows for the use of those sulfone polymer materials, provided that any specific requirements are met.

    1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this standard: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1—Reference Guide D 5033 for information and definitions related to recycled plastics.

    Note 2—There is no equivalent or similar ISO standard.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics

    D618 Practice for Conditioning Plastics for Testing

    D638 Test Method for Tensile Properties of Plastics

    D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

    D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

    D883 Terminology Relating to Plastics

    D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D3641 Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials

    D3801 Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position

    D3892 Practice for Packaging/Packing of Plastics

    D4000 Classification System for Specifying Plastic Materials

    D5630 Test Method for Ash Content in Plastics

    D5740 Guide for Writing Material Standards in the Classification Format

    D6869 Test Method for Coulometric and Volumetric Determination of Moisture in Plastics Using the Karl Fischer Reaction (the Reaction of Iodine with Water)

    D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    Underwriters Laboratories Standards

    UL94 Standard for Tests for Flammability of Plastic Materials Available from Underwriters Laboratories (UL), 333 Pfingsten Rd., Northbrook, IL 60062-2096, http://www.ul.com.

    ISO Standards

    ISO 25137-1 Sulfone Polymer moulding and Extrusion Materials--Part 1: Designation System and Basis for Specification

    ISO 25137-2 Sulfone Polymer Moulding and Extrusion Materials--Part 2: Preperation of Test Specimens and Determination of Properties


    ICS Code

    ICS Number Code 83.080.20 (Thermoplastic materials)

    UNSPSC Code

    UNSPSC Code 13102028(Polysulfone PSU)


    DOI: 10.1520/D6394-03

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top