ASTM D1556-00

    Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method


      Format Pages Price  
    PDF 7 $51.60   ADD TO CART


    1. Scope

    1.1 This test method may be used to determine the in-place density and unit weight of soils using a sand cone apparatus.

    1.2 This test method is applicable for soils without appreciable amounts of rock or coarse materials in excess of 1 1/2 in. (38 mm) in diameter.

    1.3 This test method may also be used for the determination of the in-place density and unit weight of undisturbed or in situ soils, provided the natural void or pore openings in the soil are small enough to prevent the sand used in the test from entering the voids. The soil or other material being tested should have sufficient cohesion or particle attraction to maintain stable sides on a small hole or excavation, and be firm enough to withstand the minor pressures exerted in digging the hole and placing the apparatus over it, without deforming or sloughing.

    1.4 This test method is not suitable for organic, saturated, or highly plastic soils that would deform or compress during the excavation of the test hole. This test method may not be suitable for soils consisting of unbound granular materials that will not maintain stable sides in the test hole, soils containing appreciable amounts of coarse material larger than 1 1/2 in. (38 mm), and granular soils having high void ratios.

    1.5 When materials to be tested contain appreciable amounts of particles larger than 1 1/2 in. (38 mm), or when test hole volumes larger than 0.1 ft3 (2830 cm3) are required, Test Method D4914 or D5030 are applicable.

    1.6 It is common practice in the engineering profession to concurrently use pounds to represent both a unit of mass (lbm) and a unit of force (lbf). This implicitly combines two separate systems of units, that is, the absolute system and the gravitational system. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. This test method has been written using the gravitational system of units when dealing with the inch-pound system. In this system the pound (lbf) represents a unit of force (weight). However, the use of balances or scales recording pounds of mass (lbm), or the recording of density in lbm/ft3 should not be regarded as non-conformance with this test method.

    1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D698 Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft3 (600 kN-m/m3))

    D1557 Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))

    D2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

    D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

    D4253 Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table

    D4254 Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density

    D4643 Test Method for Determination of Water (Moisture) Content of Soil by Microwave Oven Heating

    D4718 Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles

    D4753 Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing

    D4914 Test Methods for Density and Unit Weight of Soil and Rock in Place by the Sand Replacement Method in a Test Pit

    D4944 Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester

    D4959 Test Method for Determination of Water (Moisture) Content of Soil By Direct Heating

    D5030 Test Method for Density of Soil and Rock in Place by the Water Replacement Method in a Test Pit

    D6026 Practice for Using Significant Digits in Geotechnical Data


    ICS Code

    ICS Number Code 93.020 (Earth works. Excavations. Foundation construction. Underground works)

    UNSPSC Code

    UNSPSC Code 11111501(Soil)


    Referencing This Standard

    DOI: 10.1520/D1556-00

    ASTM International is a member of CrossRef.


    Citation Format

    ASTM D1556-00, Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method, ASTM International, West Conshohocken, PA, 2000, www.astm.org

    Back to Top