ASTM C1157/C1157M-09

    Historical Standard: ASTM C1157/C1157M-09 Standard Performance Specification for Hydraulic Cement

    SUPERSEDED (see Active link, below)


    Buy Standard (PDF)
    5 pages
    $50.40

    Active (view current version of standard)

    Translated Standard: Spanish
    more info


    ASTM C1157 / C1157M

    1. Scope

    1.1 This performance specification covers hydraulic cements for both general and special applications. There are no restrictions on the composition of the cement or its constituents (See Note 1).

    Note 1—There are two related hydraulic cement standards, Specification C 150 for portland cement and Specifications C 595 for blended cements, both of which contain prescriptive and performance requirements

    1.2 This performance specification classifies cements based on specific requirements for general use, high early strength, resistance to attack by sulfates, and heat of hydration. Optional requirements are provided for the property of low reactivity with alkali-silica-reactive aggregates.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice.

    1.4 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

    C114 Test Methods for Chemical Analysis of Hydraulic Cement

    C150 Specification for Portland Cement

    C151 Test Method for Autoclave Expansion of Hydraulic Cement

    C183 Practice for Sampling and the Amount of Testing of Hydraulic Cement

    C185 Test Method for Air Content of Hydraulic Cement Mortar

    C186 Test Method for Heat of Hydration of Hydraulic Cement

    C188 Test Method for Density of Hydraulic Cement

    C191 Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle

    C204 Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus

    C219 Terminology Relating to Hydraulic Cement

    C227 Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method)

    C359 Test Method for Early Stiffening of Hydraulic Cement (Mortar Method)

    C430 Test Method for Fineness of Hydraulic Cement by the 45-m (No. 325) Sieve

    C441 Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction

    C451 Test Method for Early Stiffening of Hydraulic Cement (Paste Method)

    C595 Specification for Blended Hydraulic Cements

    C596 Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

    C1012 Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution

    C1038 Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water


    ICS Code

    ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

    UNSPSC Code

    UNSPSC Code 30111601(Cement)


    DOI: 10.1520/C1157_C1157M-09

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top