SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|5||$51.60||  ADD TO CART|
1.1 This specification establishes general requirements, unless otherwise specified in the specific product specification, for ordering information, marking, and sampling for chemical analysis common to zinc and zinc alloy products and shall apply to Specifications B 6
1.2 Although this specification establishes general requirements, it does not restrict that, by agreement between customer and supplier, these requirements may be altered by a customer to suit individual need.
1.3 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This applies except where SI units only are specified.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
B6 Specification for Zinc
B69 Specification for Rolled Zinc
B86 Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings
B240 Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings
B327 Specification for Master Alloys Used in Making Zinc Die Casting Alloys
B418 Specification for Cast and Wrought Galvanic Zinc Anodes
B750 Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
B792 Specification for Zinc Alloys in Ingot Form for Slush Casting
B793 Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds
B833 Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel
B852 Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel
B860 Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing
B892 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy in Ingot Form for Die Castings
B894 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy Die Castings
B897 Specification for Configuration of Zinc and Zinc Alloy Jumbo Block and Half Block Ingot
B899 Terminology Relating to Non-ferrous Metals and Alloys
B907 Specification for Zinc, Tin and Cadmium Base Alloys Used as Solders
B908 Practice for the Use of Color Codes for Zinc Casting Alloy Ingot
B914 Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel
B943 Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications
B960 Specification for Prime Western Grade-Recycled (PWG-R) Zinc
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E88 Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition
E634 Practice for Sampling of Zinc and Zinc Alloys by Spark Atomic Emission Spectrometry
ICS Number Code 77.150.60 (Lead, zinc and tin products)
ASTM B949-08, Standard Specification for General Requirements for Zinc and Zinc Alloy Products, ASTM International, West Conshohocken, PA, 2008, www.astm.orgBack to Top