ASTM B949-06

1. Scope

1.1 This specification establishes general requirements, unless otherwise specified in the specific product specification, for ordering information, marking, and sampling for chemical analysis common to zinc and zinc alloy products and shall apply to Specifications B 6, B 69, B 86, B 240, B 327, B 418, B 750, B 792, B 793, B 833, B 852, B 860, B 892, B 894, B 897, B 907, and B 943 to the extent referenced therein.

1.2 Although this specification establishes general requirements, it does not restrict that, by agreement between customer and supplier, these requirements may be altered by a customer to suit individual need.

1.3 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification.

1.4 Units The values stated in inch-pound units are to be regarded as standard except where SI units only are specified. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B6 Specification for Zinc

B69 Specification for Rolled Zinc

B86 Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings

B240 Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings

B327 Specification for Master Alloys Used in Making Zinc Die Casting Alloys

B418 Specification for Cast and Wrought Galvanic Zinc Anodes

B750 Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings

B792 Specification for Zinc Alloys in Ingot Form for Slush Casting

B793 Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds

B833 Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel

B852 Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel

B860 Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing

B892 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy in Ingot Form for Die Castings

B894 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy Die Castings

B897 Specification for Configuration of Zinc and Zinc Alloy Jumbo Block and Half Block Ingot

B899 Terminology Relating to Non-ferrous Metals and Alloys

B907 Specification for Zinc, Tin and Cadmium Base Alloys Used as Solders

B908 Practice for the Use of Color Codes for Zinc Casting Alloy Ingot

B914 Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel

B943 Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications

E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition

E88 Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition

E634 Practice for Sampling of Zinc and Zinc Alloys by Spark Atomic Emission Spectrometry

ICS Code

ICS Number Code 77.150.60 (Lead, zinc and tin products)

DOI: 10.1520/B0949-06

ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]