ASTM B845-97(2003)

    Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts


      Format Pages Price  
    PDF 11 $58.80   ADD TO CART


    1. Scope

    1.1 The techniques described in this guide pertain to mixed flowing gas (MFG) tests containing species that are applied to evaluate devices containing electrical contacts such as slip rings, separable connectors, electromechanical relays or switch contacts. These techniques may be relevant to other devices, but it is the responsibility of the user to determine suitability prior to testing.

    1.2 The MFG tests described in this guide are designed to accelerate corrosive degradation processes. These accelerations are designed such that the degradation occurs in a much shorter time period than that expected for such processes in the intended application environment of the device being tested. Application environments can vary continuously from benign to aggressively corrosive. Connectors and contacts within closed electronic cabinets may be affected by an environment of different severity than the environment on the outside of such cabinets. In general, indoor environments are different than outdoor environments. The MFG tests described herein, being discrete embodiments of specific corrosive conditions, cannot be representative of all possible application environments. It is the responsibility of the test specifier to assure the pertinence of a given test condition to the specifier's application condition.

    1.3 The MFG tests described herein are not designed to duplicate the actual intended application environmental of the device under test. An extended bibliography, Section 10, that provides information which is useful to test specifiers to assist them in selecting appropriate test methods is included in this guide. The bibliography covers the scope from application condition characterization, single and multiple gas effects, and material and product effects to key application and test variables as well as discussions of atmospheric corrosion processes.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B542 Terminology Relating to Electrical Contacts and Their Use

    B808 Test Method for Monitoring of Atmospheric Corrosion Chambers by Quartz Crystal Microbalances

    B810 Test Method for Calibration of Atmospheric Corrosion Test Chambers by Change in Mass of Copper Coupons

    B825 Test Method for Coulometric Reduction of Surface Films on Metallic Test Samples

    B826 Test Method for Monitoring Atmospheric Corrosion Tests by Electrical Resistance Probes

    B827 Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests

    Other Documents

    EIA-364B-TP65 Mixed Industrial Gas Test Procedure Available from Electronic Industries Alliance (EIA), 2500 Wilson Blvd., Arlington, VA 22201, http://www.eia.org.

    IEC68-2–60(sec Environmental Testing--Part 2: Tests--test Ke: Flowing mixed gas corrosion test, 1995

    IECStandard68-2&ndas Basic Environmental Testing Procedures, Test Kc Sulphur Dioxide Test for Contacts and Connections Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.

    IECStandard68-2&ndas Basic Environmental Testing Procedures, Test Kd Hydrogen Sulfide Test for Contacts and Connections

    IECTechnicalTrendDoc TTD Environmental Testing, Corrosion Tests in Artificial Atmosphere at Very Low Concentration of Polluting Gas(es)

    IEEEP1156.1 Environmental Specifications for Computer Modules (Draft 4 June 10, 1992--unapproved) Available from Institute of Electrical and Electronics Engineers, Inc. (IEEE), 445 Hoes Ln., P.O. Box 1331, Piscataway, NJ 08854-1331, http://www.ieee.org.


    ICS Code

    ICS Number Code 29.120.20 (Connecting devices)

    UNSPSC Code

    UNSPSC Code 39121522(Electrical contacts)


    Referencing This Standard

    DOI: 10.1520/B0845-97R03

    ASTM International is a member of CrossRef.


    Citation Format

    ASTM B845-97(2003), Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts, ASTM International, West Conshohocken, PA, 2003, www.astm.org

    Back to Top