1. Scope
1.1 This specification covers corrugated aluminum alloy structural plate used in the construction of pipe, pipe-arches, arches, underpasses, box culverts, and special shapes for field assembly. Appropriate fasteners are also described. The pipe, arches, and other shapes are generally used for drainage purposes, pedestrian and vehicular underpasses, and utility tunnels. Aluminum box culvert shapes are covered in Specification B 864/B 864M.
1.2 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and plate thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of plate thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the plate thickness. The structural design of corrugated aluminum structural plate pipe and the proper installation procedures are given in Practices B 790/B 790M and B 789/B 789M, respectively. A procedure for using life-cycle cost analysis techniques to evaluate alternate drainage system designs using corrugated metal pipe is given in Practice A 930.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
A307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength
A325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
A563 Specification for Carbon and Alloy Steel Nuts
A563M Specification for Carbon and Alloy Steel Nuts (Metric)
A930 Practice for Life-Cycle Cost Analysis of Corrugated Metal Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits
B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate
B209M Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)
B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
B221M Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)
B666/B666M Practice for Identification Marking of Aluminum and Magnesium Products
B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
B789/B789M Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
B790/B790M Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
B864/B864M Specification for Corrugated Aluminum Box Culverts
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
F467 Specification for Nonferrous Nuts for General Use
F467M Specification for Nonferrous Nuts for General Use (Metric)
F468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
F468M Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric)
F593 Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
F594 Specification for Stainless Steel Nuts
F738M Specification for Stainless Steel Metric Bolts, Screws, and Studs
F836M Specification for Style 1 Stainless Steel Metric Nuts (Metric)
American National Standards
B18.2.4.6M Hex Nuts, Heavy, Metric
Keywords
aluminum structural plate; arches; culverts; field bolted structures; pipe; pipe arches;
ICS Code
ICS Number Code 77.150.10 (Aluminium products)
DOI: 10.1520/B0746_B0746M-02
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
