ASTM B679-98

1. Scope

1.1 Purity -This specification covers requirements for electrodeposited palladium coatings containing at least 99.7 mass % of palladium metal.

1.2 Properties -Palladium is the lightest and least noble of the platinum group metals. It has a specific gravity of 12.0, which is substantially less than gold (19.3) and platinum (21.5). This yields a greater volume or thickness of coating and, consequently, some saving of metal weight accompanied by a small sacrifice in corrosion resistance and reflectivity. The hardness range of electrodeposited palladium compares favorably with the other electroplated noble metals and their alloys.

1.3 The values stated in SI units are the preferred values. Values provided in parentheses are for information only.

1.4 The following hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B183 Practice for Preparation of Low-Carbon Steel for Electroplating

B242 Guide for Preparation of High-Carbon Steel for Electroplating

B254 Practice for Preparation of and Electroplating on Stainless Steel

B281 Practice for Preparation of Copper and Copper-Base Alloys for Electroplating and Conversion Coatings

B322 Guide for Cleaning Metals Prior to Electroplating

B343 Practice for Preparation of Nickel for Electroplating with Nickel

B374 Terminology Relating to Electroplating

B481 Practice for Preparation of Titanium and Titanium Alloys for Electroplating

B482 Practice for Preparation of Tungsten and Tungsten Alloys for Electroplating

B487 Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section

B488 Specification for Electrodeposited Coatings of Gold for Engineering Uses

B489 Practice for Bend Test for Ductility of Electrodeposited and Autocatalytically Deposited Metal Coatings on Metals

B499 Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals

B507 Practice for Design of Articles to Be Electroplated on Racks

B542 Terminology Relating to Electrical Contacts and Their Use

B558 Practice for Preparation of Nickel Alloys for Electroplating

B567 Test Method for Measurement of Coating Thickness by the Beta Backscatter Method

B568 Test Method for Measurement of Coating Thickness by X-Ray Spectrometry

B571 Practice for Qualitative Adhesion Testing of Metallic Coatings

B602 Test Method for Attribute Sampling of Metallic and Inorganic Coatings

B689 Specification for Electroplated Engineering Nickel Coatings

B697 Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic Coatings

B741 Test Method for Porosity In Gold Coatings On Metal Substrates By Paper Electrography

B748 Test Method for Measurement of Thickness of Metallic Coatings by Measurement of Cross Section with a Scanning Electron Microscope

B762 Test Method of Variables Sampling of Metallic and Inorganic Coatings

B765 Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings

B799 Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor

B809 Test Method for Porosity in Metallic Coatings by Humid Sulfur Vapor (Flowers-of-Sulfur)

D1125 Test Methods for Electrical Conductivity and Resistivity of Water

D3951 Practice for Commercial Packaging

ICS Code

ICS Number Code 25.220.40 (Metallic coatings)

DOI: 10.1520/B0679-98

ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]