1. Scope
1.1 This specification covers rod of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06035, N06455, N06058, and N06059)*, low-carbon nickel-molybdenum-chromium-tantalum (UNS N06210), low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenum-tungsten (UNS N06686) as shown in Table 1, for use in general corrosive service.
1.2 The following products are covered under this specification:
1.2.1 Rods 5/16to 3/4 in. (7.94 to 19.05 mm), exclusive, in diameter, hot or cold finished, solution annealed and pickled, or mechanically descaled.
1.2.2 Rods 3/4to 31/2 in. (19.05 to 88.9 mm), inclusive, in diameter, hot or cold finished, solution annealed, ground or turned.
1.2.3 Rods 1/4 to 3 1/2 in. (6.35 to 88.9 mm), inclusive, in diameter, solution annealed, cold finished, as cold finished, ground or turned (N06059 and N06686 only, see Table 2 and Table 3).
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
Keywords
N06022; N06035; N06058; N06059; N06200; N06210; N06455; N06686; N10276; N10362; rod; Corrosive service applications--bars/rods/shapes; Low-carbon nickel alloys--specifications; Nickel alloy rod/bar/wire--specifications; Nickel-chromium alloys--specifications; Nickel-chromium-molybdenum alloys--specifications; Nickel-molybdenum alloys--specifications; Nickel-molybdenum-chromium alloys--specifications; UNS N06022 (Ni-Cr-Mo alloy, Hastelloy C-22); UNS N06058 (low-carbon Ni-Cr-Mo alloy); UNS N06059 (low carbon Ni-Cr-Mo alloy, Alloy 59); UNS N06200 (Ni-Cr-Mo-Cu alloy, Hastelloy C-2000); UNS N06455 (Ni-Cr alloy, Hastelloy C-4); UNS N06686 (Ni-Cr-Mo-W alloy, Inconel 686); UNS N10276 (Ni-Mo alloy, Hastelloy C276)
ICS Code
DOI: 10.1520/B0574-06E01
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
