1.1 This specification covers electric fusion welded UNS N08020, UNS N08026, and UNS N08024* pipe suitable for high-temperature or corrosive service. (Although no restrictions are placed on the sizes of pipe that may be furnished under this specification, commercial practice is commonly limited to sizes not less than 8 in. (203 mm) nominal diameter.)
1.2 Two types of pipe are covered as follows:
1.2.1 Type I -All welded joints to be completely examined by radiography.
1.2.2 Type II -No radiographic examination required.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
B127 Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
B162 Specification for Nickel Plate, Sheet, and Strip
B168 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Plate, Sheet, and Strip
B333 Specification for Nickel-Molybdenum Alloy Plate, Sheet, and Strip
B424 Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825, UNS N08221, and UNS N06845) Plate, Sheet, and Strip
B435 Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
B443 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy(UNS N06625) and Nickel-Chromium-Molybdenum-SiliconAlloy (UNS N06219) Plate, Sheet, and Strip
B463 Specification for UNS N08020 Alloy Plate, Sheet, and Strip
B536 Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Plate, Sheet, and Strip
B575 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Plate, Sheet, and Strip
B582 Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and Strip
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
B899 Terminology Relating to Non-ferrous Metals and Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
American Society of Mechanical Engineers Standard
ASME Boiler and Pressure Vessel Code, Section IX and Section VIII, Div. 1
fusion welded; high-temperature alloy; pipe; Carpenter alloy--specifications; Chromium-nickel-iron-molybdenum-copper alloy--pipe/tube; Corrosion--metals/alloys; Corrosion--pipe/tube materials/systems; Corrosive service applications--pipe (Ni/Ni alloy); Electric-fusion-welded Ni/Ni alloy pipe; High-temperature service applications--nickel (specifications); Nickel alloy pipe--specifications; Nickel-chromium alloys--specifications; Nickel-iron alloy--specifications; Nickel-iron-chromium alloys--specifications; UNS N08020 (Ni-Fe-Cr alloy, Carpenter 20Cb3)--pipe; UNS N08024 (Cr-Ni-Fe-Mo-Cu alloy, columbium stabilized); UNS N08026 (Ni-Cr wrought alloy, Carpenter 20Mo6); Welded Ni/Ni alloy pipe--specifications;
ICS Number Code 77.150.40 (Nickel and chromium products)
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]