1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
AExcept Copper UNS No. C10300 (oxygen-free extra low phosphorus), No. C10800 (oxygen-free low phosphorus), and C10910 (low oxygen), these types of copper are classified in Classification B 224.
|Copper UNS No.||Previous DesignationA||Type of Copper|
|C10100|| OFE||Oxygen-free electronic|
|C10200B||OF|| Oxygen-free without residualdeoxidants|
|C10300|| ...||Oxygen-free extra low phosphorus|
|C10400, C10500, C10700||OFS|| Oxygen-free, silver bearing|
|C10800|| ...||Oxygen-free low phosphorus|
|C10910|| ...||Low oxygen|
|C11000B||ETP|| Electrolytic tough pitch|
|C11300, C11400, C11600B||STP|| Silver bearing tough pitch|
|C12000|| DLP||Phosphorized, low residual phos-phorus|
|C12200B||DHP|| Phosphorized, high residual phos-phorus|
|C12300|| DPS||Phosphorized, silver bearing|
|C14200|| DPA||Phosphorus deoxidized, arsenical|
|C14420|| ...||Tin bearing tellurium copper|
|C14530|| ...||Tin tellurium bearing copper|
BSAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for Copper UNS No. C12200.
Note 1--Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the supplier to determine which copper would be best suited for the intended application.
Note 2--Copper UNS Nos. C10400, C10500, C10700, C11300, C11400, and C11600 identify coppers with specific silver content (see Table 1 ).
Note 3--This specification is not intended to cover material rolled to ounce-weight thicknesses. Such material is covered by Specification B370.
Plates for locomotive fireboxes are covered by Specification B 11.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are also covered by Specification B72.
1.1.1 When no specific copper is identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.
1.3The following safety hazards caveat only pertains to the test method portion, Section 14 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
B11 Specification for Copper Plates for Locomotive Fireboxes
B170 Specification for Oxygen-Free Electrolytic Copper--Refinery Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B216 Specification for Tough-Pitch Fire-Refined Copper--Refinery Shapes
B224 Classification of Coppers
B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
B272 Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)
B370 Specification for Copper Sheet and Strip for Building Construction
B577 Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in Copper
B601 Classification for Temper Designations for Copper and Copper Alloys--Wrought and Cast
B846 Terminology for Copper and Copper Alloys
E3 Guide for Preparation of Metallographic Specimens
E8 Test Methods for Tension Testing of Metallic Materials
E8M Test Methods for Tension Testing of Metallic Materials [Metric]
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E112 Test Methods for Determining Average Grain Size
E478 Test Methods for Chemical Analysis of Copper Alloys
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASME Boiler Pressure Vessel Code Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.
annealed; copper bars; copper plate; copper sheet; copper strip ; hot-rolled; rolled; UNS No. C10100; UNS No. C10200; UNS No. C10300; UNS No. C10400; UNS No. C10500; UNS No. C10700; UNS No. C10800; UNS No. C10910; UNS No. C11000; UNS No. C11300; UNS No. C11400; UNS No. C11600; UNS No. C12000; UNS No. C12200; UNS No. C12300; UNS No. C14200; UNS No. C14420; UNS No. C14530; ICS Number Code 4530; 77.150.30 (Copper products)
ICS Number Code 77.150.30 (Copper products)
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]