ASTM B124/B124M-13

    Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes


      Format Pages Price  
    PDF 7 $51.60   ADD TO CART


    1. Scope

    1.1 This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging. The following coppers and copper alloys are involved:

    Copper UNS Nos.

    Copper Alloy UNS Nos.

     

     

    C11000

    C35330

    C14500

    C36500

    C14700

    C37000

     

    C37700

     

    C46400

     

    C48200

     

    C48500

     

    C48600

     

    C49250

     

    C49255

     

    C49260

     

    C49300

     

    C49340

     

    C49350

     

    C49355

     

    C49360

     

    C61900

     

    C62300

     

    C63000

     

    C63200

     

    C64200

     

    C64210

     

    C65500

     

    C67500

     

    C67600

     

    C69150

     

    C69300

     

    C70620

     

    C71520

     

    C77400

     

    C87700

     

    C87710

     

    C27450




    Note 1Additional information about forging practice and forgings produced from these alloys is given in Appendix X1 and in Specification B283.

    1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Other Standards

    ISO 3110, Part 2 (T Determination of Aluminum Content: Flame Atomic Absorption Spectrometric Method Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.

    JIS H 1068:2005 Methods for Determination of Bismuth in Copper and Copper Alloys Available from Japanese Standards Organization (JSA), 4-1-24 Akasaka Minato-Ku, Tokyo 107-8440, Japan, http://www.jsa.or.jp. (Japanese Industrial Standards)

    ASTM Standards

    B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

    B283/B283M Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)

    E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes

    E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)

    E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys

    E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys

    E121 Test Methods for Chemical Analysis of Copper-Tellurium Alloys

    E478 Test Methods for Chemical Analysis of Copper Alloys


    UNSPSC Code

    UNSPSC Code 30262200(Copper bars); 30102409(Copper rods)


    Referencing This Standard

    DOI: 10.1520/B0124_B0124M-13

    ASTM International is a member of CrossRef.


    Citation Format

    ASTM B124 / B124M-13, Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes, ASTM International, West Conshohocken, PA, 2013, www.astm.org

    Back to Top