|
|
|
ASTM A990-06
Historical Standard: ASTM A990-06 Standard Specification for Castings, Iron-Nickel-Chromium and Nickel Alloys, Specially Controlled for Pressure Retaining Parts for Corrosive Service
SUPERSEDED
(see Active link, below)
1. Scope
1.1 This specification covers iron-nickel-chromium and nickel alloy castings specially processed with restricted melt practices, weldability testing, and nondestructive examination (NDE) requirements. 1.2 A number of grades of iron-nickel-chromium and nickel alloy castings are included in this specification. Since these grades possess varying degrees of suitability for service in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and corrosion-resistant characteristics. 1.3 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)  The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A351/A351M Specification for Castings, Austenitic, for Pressure-Containing Parts
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A488/A488M Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel
A494/A494M Specification for Castings, Nickel and Nickel Alloy
A703/A703M Specification for Steel Castings, General Requirements, for Pressure-Containing Parts
A743/A743M Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application
A744/A744M Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service
A802/A802M Practice for Steel Castings, Surface Acceptance Standards, Visual Examination
A903/A903M Specification for Steel Castings, Surface Acceptance Standards, Magnetic Particle and Liquid Penetrant Inspection
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A985/A985M Specification for Steel Investment Castings General Requirements, for Pressure-Containing Parts
E94 Guide for Radiographic Examination
E165 Practice for Liquid Penetrant Examination for General Industry
E186 Reference Radiographs for Heavy-Walled (2 to 412-in. (50.8 to 114-mm)) Steel Castings
E272 Reference Radiographs for High-Strength Copper-Base and Nickel-Copper Alloy Castings
E280 Reference Radiographs for Heavy-Walled (412 to 12-in. (114 to 305-mm)) Steel Castings
E446 Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness
ASME/ANSI Standard
ASME/ANSIB16.34, Valves-Flanged, Threaded, and Welding End
AWS Standards
AWSA5.14/A5.14M, Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods
Keywords
casting; iron-nickel-chromium; nickel alloy; pressure retaining; Iron-nickel-chromium alloys--specifications; Nickel alloy castings--specifications; Nondestructive evaluation (NDE)--metallic materials; Corrosive service applications--castings ;
ICS Code
ICS Number Code 77.120.40 (Nickel, chromium and their alloys)
DOI: 10.1520/A0990-06
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
|
Standards Tracker
Standards Subscriptions
|
|
|
|
|
