SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|5||$54.00||  ADD TO CART|
1.1 This specification covers composite ribbed steel pipe, precoated and polyethylene lined intended for use for gravity flow sanitary sewers, storm sewers, and other special applications such as water transmission pipe, rehabilitation pipe, slip line pipe, and irrigation pipe where extra corrosion and abrasion resistance are required. The steel sheet used in the fabrication of the pipe has a polymer coating over a metallic coating of zinc on both sides. In addition, as the pipe is being fabricated, the ribs are filled with polyethylene and then a polyethylene liner is extruded onto the interior surface.
1.2 The exterior polymer precoating provides extra protection of the steel against soilside corrosion, in addition to that provided by the metallic coating, and also provides a dielectric barrier for cathodic protection. The interior polymer precoating provides an adhesive layer between the galvanized steel and the polyethylene lining. The applied lining provides internal protection against corrosion, erosion, and abrasion. By filling the rib which has a deltoid shape (smaller at the opening in the pipe wall than at the bottom of the rib), the polyethylene is mechanically connected to the pipe wall and the polyethylene liner is then thermally bonded to the filled rib.
1.3 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheet thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The installation procedure is described in Practice A 798.
1.4 This specification is applicable to orders in either inch-pound units as A 978, or in SI units as A 978M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the material is ordered to A 978M.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
A307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength
A563 Specification for Carbon and Alloy Steel Nuts
A563M Specification for Carbon and Alloy Steel Nuts (Metric)
A742/A742M Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe
A780 Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings
A796/A796M Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications
A798/A798M Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other Applications
A902 Terminology Relating to Metallic Coated Steel Products
A926 Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe
A929/A929M Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe
B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel
B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
C443 Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets
C443M Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets (Metric)
D638 Test Method for Tensile Properties of Plastics
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
D1056 Specification for Flexible Cellular Materials--Sponge or Expanded Rubber
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1435 Practice for Outdoor Weathering of Plastics
D2240 Test Method for Rubber Property--Durometer Hardness
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D5576 Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR)
D5630 Test Method for Ash Content in Plastics
F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric)
F593 Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
F594 Specification for Stainless Steel Nuts
F738M Specification for Stainless Steel Metric Bolts, Screws, and Studs
F836M Specification for Style 1 Stainless Steel Metric Nuts (Metric)
AASHTO StandardLRFD Bridge Construction Specifications, Section 2 Standard Specifications for Highway Bridges, Division II, Section 26 T 249 Test for Helical Lock Seam Corrugated Pipe
UNSPSC Code 40171500(Commercial pipe and piping)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM A978 / A978M-97(2002), Standard Specification for Composite Ribbed Steel Pipe, Precoated and Polyethylene Lined for Gravity Flow Sanitary Sewers, Storm Sewers, and Other Special Applications, ASTM International, West Conshohocken, PA, 1997, www.astm.orgBack to Top