1. Scope
1.1 This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications under any of the following individual product specifications:
| Title of Specification | ASTM Designation |
| |
| Forgings, Carbon Steel, for Piping Components | A105/A105M |
| Forgings, Carbon Steel, for General-Purpose Piping | A181/A181M |
| Forged or Rolled Alloy-Steel Pipe Flanges, Forged | A182/A182M |
Fittings, and Valves and Parts for High Temperature
Service | |
| Forgings, Carbon and Low Alloy Steel, Requiring Notch | A350/A350M |
| Toughness Testing for Piping Components | |
| Forged or Rolled 8 and 9 % Nickel Alloy | A522/A522M |
| Steel Flanges, Fittings, Valves, and Parts | |
| for Low-Temperature Service | |
| Forgings, Carbon and Alloy Steel, for Pipe Flanges, | A694/A694M |
Fittings, Valves, and Parts for High-Pressure
Transmission Service | |
| Flanges, Forged, Carbon and Alloy Steel for Low | A707/A707M |
| Temperature Service | |
| Forgings, Carbon Steel, for Piping Components with | A727/A727M |
| Inherent Notch Toughness | |
| Forgings, Titanium-Stabilized Carbon Steel, for | A836/A836M |
| Glass-Lined Piping and Pressure Vessel Service | |
1.2 In case of conflict between a requirement of the individual product specification and a requirement of this general requirement specification, the requirements of the individual product specification shall prevail over those of this specification.
1.3 By mutual agreement between the purchaser and the supplier, additional requirements may be specified (see Section 4.1.2). The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon between the purchaser and supplier.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text and the tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply, unless the “M” designation (SI) of the product specification is specified in the order.
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A105/A105M Specification for Carbon Steel Forgings for Piping Applications
A181/A181M Specification for Carbon Steel Forgings, for General-Purpose Piping
A182/A182M Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
A275/A275M Practice for Magnetic Particle Examination of Steel Forgings
A350/A350M Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A522/A522M Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service
A694/A694M Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A707/A707M Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service
A727/A727M Specification for Carbon Steel Forgings for Piping Components with Inherent Notch Toughness
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A836/A836M Specification for Titanium-Stabilized Carbon Steel Forgings for Glass-Lined Piping and Pressure Vessel Service
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A967 Specification for Chemical Passivation Treatments for Stainless Steel Parts
A991/A991M Test Method for Conducting Temperature Uniformity Surveys of Furnaces Used to Heat Treat Steel Products
A1058 Test Methods for Mechanical Testing of Steel Products--Metric
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
E165 Practice for Liquid Penetrant Examination for General Industry
E381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
E709 Guide for Magnetic Particle Testing
E1916 Guide for Identification of Mixed Lots of Metals
ASME Standard
ASME Boiler and Pressure Vessel Code-Section IX
Manufacturers Standardization Society Standard
SP 25 Standard Marking System of Valves, Fittings, Flanges and Unions
Keywords
alloy steel; carbon steel; fittings; flanges; forgings; general requirement; piping applications; pressure containing parts; stainless steel; temperature service applications—elevated; temperature service applications—high; valves;
ICS Code
ICS Number Code 23.040.01 (Pipeline components in general. Pipelines); 77.140.20 (Steels of high quality)
DOI: 10.1520/A0961_A0961M-12
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
