SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|16||$60.00||  ADD TO CART|
1.1 This specification covers deformed and plain steel reinforcing bars which prior to surface preparation are prefabricated and then coated with a protective fusion-bonded epoxy coating by electrostatic spray or other suitable method.
1.2 Prefabricated steel reinforcing bars coated with fusion-bonded epoxy formulations in accordance with this specification are not intended to be bent or rebent.
Note 1--Experience has shown epoxy-coated prefabricated steel reinforcing bars have limited capability to be successfully field bent or rebent (see 9.3.1). If the construction project requires epoxy-coated steel reinforcing bars that must be able to sustain field bending or rebending, the use of coated bars conforming to Specification A775/A775M should be considered.
1.3 Organic coatings other than epoxy may be used provided they meet the requirements of this specification.
1.4 Requirements for epoxy coatings are contained in Annex A1.
1.5 Guidelines for application process and product test procedures of epoxy coatings for steel reinforcing bars are presented in Appendix X1.
1.6 Guidelines for construction practices at the job-site for coated steel reinforcing bars are presented in Appendix X2.
1.7 This specification is applicable for orders in either SI (metric) units (as Specification A934M) or inch-pound units [as Specification A934].
1.8 The values stated in either SI or inch-pound units are to be regarded as standard. Within the text, the inch-pound units are shown in brackets. The values stated in the two systems are not exact equivalents: therefore, each system must be used independently of the other. Combining values from the systems may result in nonconformance with this specification.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
A775/A775M Specification for Epoxy-Coated Steel Reinforcing Bars
A944 Test Method for Comparing Bond Strength of Steel Reinforcing Bars to Concrete Using Beam-End Specimens
A996/A996M Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement
B117 Practice for Operating Salt Spray (Fog) Apparatus
D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
G8 Test Methods for Cathodic Disbonding of Pipeline Coatings
G14 Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)
G20 Test Method for Chemical Resistance of Pipeline Coatings
G42 Test Method for Cathodic Disbonding of Pipeline Coatings Subjected to Elevated Temperatures
G62 Test Methods for Holiday Detection in Pipeline Coatings
NACE International StandardRP 0287 Field Measurement of Surface Profile of Abrasive Blast Cleaned Steel Surfaces Using a Replica Tape
Society for Protective Coatings SpecificationsSSPC-PA 2 Measurement of Dry Coating Thickness with Magnetic Gages SSPC-SP 10 Near-White Blast Cleaning SSPC-VIS 1 Pictorial Surface Preparation Standards for Painting Steel Surfaces
American Concrete Institute SpecificationsACI 301 Specifications for Structural Concrete ACI 315 Details and Detailing of Concrete Reinforcement
ICS Number Code 77.140.15 (Steels for reinforcement of concrete)
UNSPSC Code 30103623(Reinforcing bar or rebar or mesh)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM A934 / A934M-00b, Standard Specification for Epoxy-Coated Prefabricated Steel Reinforcing Bars, ASTM International, West Conshohocken, PA, 2001, www.astm.orgBack to Top