ASTM A888-13

    Historical Standard: ASTM A888-13 Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

    SUPERSEDED (see Active link, below)


    Buy Standard (PDF)
    58 pages
    $80.40

    Active (view current version of standard)


    ASTM A888

    1. Scope

    1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

    1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.

    1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.2

    1.3.1 Lengths:

     

    Figures

    EDP/ASA Identification Numbers
    for Hubless Pipe

    Fig. 1

    10 ft (3.0 m) in sizes and 5 ft. (1.5 m)
    11/2 , 2, 3, 4, 5, 6, 8,
    10, 12, and 15 in.

    Fig. 1, Fig. 2

    Method of Specifying Fittings

    Fig. 3


    1.3.2 Fittings:

    Quarter Bend

    Fig. 5

    Quarter Bend, Reducing

    Fig. 6

    Quarter Bend, With Side Opening

    Fig. 7

    Quarter Bend, With Heel Opening

    Fig. 8

    Quarter Bend, Tapped

    Fig. 9

    Quarter Bend, Double

    Fig. 10

    Quarter Bend, Long

    Fig. 11

    Short Sweep

    Fig. 12

    Long Sweep

    Fig. 13

    Long Sweep, Reducing

    Fig. 14

    Fifth Bend

    Fig. 15

    Sixth Bend

    Fig. 16

    Eighth Bend

    Fig. 17

    Eighth Bend Long

    Fig. 18

    Sixteenth Bend

    Fig. 19

    Sanitary Tee

    Fig. 20

    Sanitary Tee With Side Opening

    Fig. 21

    Sanitary Tee With 2 in. Side Opening R or L/R and L

    Fig. 22

    Sanitary Tee, New Orleans Special With Side Opening

    Fig. 23

    Sanitary Tee With 45° Side Openings and New Orleans

    Fig. 24

    Sanitary Special Tee Tapped

    Fig. 25

    Sanitary Tapped Tee, Horizontal Twin

    Fig. 26

    Sanitary Tapped Tee, Double Vertical

    Fig. 27

    Y Branch

    Fig. 28

    Y Branch, Double

    Fig. 29

    Y Branch, Upright

    Fig. 30

    Upright Y Wide Center Florida Special

    Fig. 31

    Y Branch, Combination 1/8 Bend

    Fig. 32

    Y Branch, Combination 1/8 Bend Double

    Fig. 33

    Sanitary Cross

    Fig. 34

    Sanitary Cross With Side Opening

    Fig. 35

    Sanitary Cross, New Orleans, With Side Openings

    Fig. 36

    Sanitary Cross, New Orleans, With 45° Special and
     Regular Side Openings

    Fig. 37

    Sanitary Cross, Tapped

    Fig. 38

    Test Tee

    Fig. 39

    Tapped, Extension Piece

    Fig. 40

    Increaser-Reducer

    Fig. 41

    Increaser-Reducer, Short

    Fig. 42

    Tapped Adapter

    Fig. 43

    Blind Plug

    Fig. 44

    Iron Body Cleanout-Tapped

    Fig. 45

    P Trap

    Fig. 46

    P Trap, Long

    Fig. 47

    P Trap, Deep Seal

    Fig. 48

    P Trap, With Primer

    Fig. 49

    P Trap, With Tapped Inlet

    Fig. 50

    Tapped Inlet, Double

    Fig. 51

    Modified Combination Wye and 1/8  Bend, Double

    Fig. 52

    Modified Combination Wye and 1/8  Bend, Double, Extended

    Fig. 53

    Two-Way Cleanout

    Fig. 54

    Twin Cleanout

    Fig. 55

    Closet Bend, Regular and Reducing

    Fig. 56

    Closet Flange Riser

    Fig. 57

    Tapping Bosses

    Fig. 58

    Double Sweep Sanitary Tee (Extended)

    Fig. 59

    Running Trap with Double Vents

    Fig. 60

    P Trap with Tapped or Hubless Side Inlet

    Fig. 61

    Vented Tub Wye Extended, Double

    Fig. 62

    Vented Tub Wye Extended Offset, Left or Right

    Fig. 63

    Vented Tub Wye

    Fig. 64

    Double Two Way Cleanout

    Fig. 65


    1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.5 The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301.

    Note 1The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A48/A48M Specification for Gray Iron Castings

    A644 Terminology Relating to Iron Castings

    D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

    D3960 Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings

    E8 Test Methods for Tension Testing of Metallic Materials

    E1645 Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis

    E2349 Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies)

    Military Standard

    MIL-STD-129 Military Marking for Shipment and Storage

    ANSI/ASME Standard

    B1.20 Pipe Threads

    Other Documents

    CastIronSoilPipeInst Specification 301 Available from Cast Iron Soil Pipe Institute (CISPI), 1064 Delaware Ave SE, Atlanta, GA 30316, http://www.cispi.org.

    NationalMotorFreight

    UniformFreightClassi


    ICS Code

    ICS Number Code 23.040.01 (Pipeline components in general. Pipelines); 91.140.80 (Drainage systems)

    UNSPSC Code

    UNSPSC Code 31100000(Castings and casting assemblies); 40170000(Pipe piping and pipe fittings)


    DOI: 10.1520/A0888-13

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top