ASTM A849-00

    Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF 7 $51.60   ADD TO CART


    1. Scope

    1.1 This specification covers post-applied coatings, pavings, and linings for corrugated steel pipe and corrugated steel structural plate pipe, pipe-arches, and arches coated, paved, or lined with specified materials over either metallic coatings or metallic coatings with polymer coatings. This specification includes asphalt, polymerized asphalt, polymer, mastic, and emulsion coatings and asphalt and concrete pavements and linings applied to the pipe in the producing plant, as well as, asphalt and mastic coatings applied in the field. Field-applied concrete pavements and linings are covered by Specification A979/A979M. The pipe to which the coatings are applied is described in Specifications A760/A760M, A761/A761M, and A762/ A762M.

    1.2 There is no cleaning operation currently included in pipe coating practice. However, experience has shown that a clean substrate provides good adherence for both cold- and hot-applied post coatings. The performance of post coating or lining, or both, will depend on the surface cleanliness over which it is applied.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.

    1.4 The following safety hazards caveat pertains only to the test methods portions, Sections 10 and 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete

    A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

    A742/A742M Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe

    A760/A760M Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains

    A761/A761M Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches

    A762/A762M Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and Drains

    A862/A862M Practice for Application of Asphalt Coatings to Corrugated Steel Sewer and Drainage Pipe

    A926 Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe

    A979/A979M Specification for Concrete Pavements and Linings Installed in Corrugated Steel Structures in the Field

    C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field

    C33 Specification for Concrete Aggregates

    C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens

    C150 Specification for Portland Cement

    C309 Specification for Liquid Membrane-Forming Compounds for Curing Concrete

    C595 Specification for Blended Hydraulic Cements

    C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete

    C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials

    D5 Test Method for Penetration of Bituminous Materials

    D6 Test Method for Loss on Heating of Oil and Asphaltic Compounds

    D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

    D70 Test Method for Density of Semi-Solid Bituminous Materials (Pycnometer Method)

    D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester

    D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers

    D1187 Specification for Asphalt-Base Emulsions for Use as Protective Coatings for Metal

    D2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene

    D4402 Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer


    ICS Code

    ICS Number Code 23.040.10 (Iron and steel pipes)

    UNSPSC Code

    UNSPSC Code 40171500(Commercial pipe and piping)


    DOI: 10.1520/A0849-00

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top