ASTM A815/A815M-07a

    Standard Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping Fittings

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF Version 7 $50.40   ADD TO CART


    1. Scope

    1.1 This specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction covered by the latest revision of Specification A 960/A 960M. Fittings differing from these standards may be furnished in accordance with Supplementary Requirement S8.

    1.1.1 Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. They are manufactured to the requirements of Specification A 960/A 960M, and they shall have pressure ratings compatible with . Class WP-S fittings are those manufactured from seamless product by a seamless method of manufacture (marked with class symbol WP-S); Class WP-W fittings are those which contain welds where the fitting fabrication or construction welds have been radiographed (marked with class symbol WP-W); and Class WP-WX fittings are those which contain welds where all welds have been radiographed (marked with class symbol WP-WX); and Class WP-WU fittings are those which contain welds where all welds have been ultrasonically tested (marked with class symbol WP-WU).

    1.1.2 Class CR fittings are those manufactured to the requirements of MSS SP-43, and they shall have pressure ratings compatible with .

    1.2 This specification does not apply to cast fittings.

    1.3 Optional supplementary requirements are provided. When desired, one or more of these may be specified in the order.

    1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable "M" specification designation [SI units], the material shall be furnished to inch-pound units.

    1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

    A388/A388M Practice for Ultrasonic Examination of Steel Forgings

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A763 Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels

    A923 Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels

    A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings

    E165 Practice for Liquid Penetrant Examination for General Industry

    ASME Standards

    B16.11 Forged Fittings, Socket-Welding and Threaded

    B16.9 Factory-Made Wrought Butt-Welding Fittings

    MSS Standards

    MSSSP-43 Standard Practice for Light Weight Stainless Steel Butt-Welding Fittings

    MSSSP-79 Socket-Welding Reducer Inserts

    MSSSP-83 Steel Pipe Unions, Socket-Welding and Threaded

    MSSSP-95 Swage(d) Nipples and Bull Plugs

    MSSSP-97 Integrally Reinforced Forged Branch Outlet Fittings--Socket Welding, Threaded and Buttwelding Ends


    ICS Code

    ICS Number Code 23.040.40 (Metal fittings)

    UNSPSC Code

    UNSPSC Code 40171600(Industrial pipe and piping)


    DOI: 10.1520/A0815_A0815M-07A

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top