ASTM A814/A814M-03

    Standard Specification for Cold-Worked Welded Austenitic Stainless Steel Pipe

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF 6 $50.40   ADD TO CART


    1. Scope

    1.1 This specification covers two classes of flanged and cold-bending quality cold-worked straight-seam single or double welded austenitic steel pipe intended for high-temperature and general corrosive services.

    Note 1—When the impact test criterion for a low-temperature service would be 15 ftlbf [20 J] energy absorption or 15 mils [0.38 mm] lateral expansion, some of the austenitic stainless steel grades covered by this specification are accepted by certain pressure vessel or piping codes without the necessity of making the actual test. For example, Grades 304, 304L, and 347 are accepted by the ASME Pressure Vessel Code, Section VIII Division 1, and by the Chemical Plant and Refinery Piping Code, ANSI B31.3 for service at temperatures as low as -425°F [-250°C] without qualification by impact tests. Other AISI stainless steel grades are usually accepted for service temperatures as low as -325°F [-200°C] without impact testing. Impact testing may, under certain circumstances, be required. For example, materials with chromium or nickel content outside the AISI ranges, and for material with carbon content exceeding 0.10 %, are required to be impact tested under the rules of ASME Section VIII Division 1 when service temperatures are lower than -50°F [-45°C].

    1.2 Grades TP304H, TP304N, TP316H, TP316N, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP316, TP321, TP347, and TP348, and are intended for high-temperature service.

    1.3 Two classes of pipe are covered as follows:

    1.3.1 Class SW—Pipe, single-welded with no addition of filler metal and

    1.3.2 Class DW—Pipe, double-welded with no addition of filler metal.

    1.4 Optional supplementary requirements are provided for pipe where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, one or more of these may be specified in the order.

    1.5 Table 1 lists the dimensions of cold-worked single- or double-welded stainless steel pipe. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification.

    1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

    A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe

    E112 Test Methods for Determining Average Grain Size

    E381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    ASME Boiler and Pressure Vessel Code

    SectionVIIIDivision1 Pressure Vessels

    SAE Standard

    SAEJ1086 Practice for Numbering Metals and Alloys (UNS)


    ICS Code

    ICS Number Code 23.040.10 (Iron and steel pipes)

    UNSPSC Code

    UNSPSC Code 40171621(Industrial welded stainless steel pipe)


    DOI: 10.1520/A0814_A0814M-03

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top