ASTM A635/A635M-00

    Historical Standard: ASTM A635/A635M-00 Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Carbon, Commercial Steel, Drawing Steel, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, Hot-Rolled, General Requirements

    SUPERSEDED (see Active link, below)


    Buy Standard (PDF)
    10 pages
    $50.40

    Active (view current version of standard)


    ASTM A635 / A635M

    1. Scope

    1.1 This specification covers hot-rolled, heavy-thickness, carbon commercial steel, drawing steel, structural steel, high-strength low-alloy, and high-strength low-alloy with improved formability sheet and strip. Structural steel may be ordered when the coils are intended for conversion to plate steels. It is included for that purpose only.

    1.2 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.

    1.3 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the "M" specification is used.

    Note 1—The term weight is used when inch-pound units are the standard. However, under SI, the preferred term is mass.

    1.4 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

    1.5 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A414/A414M Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels

    A424/A424M Specification for Steel, Sheet, for Porcelain Enameling

    A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

    A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A1018/A1018M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

    A1031 Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    Federal Standards

    Fed.Std.No.123 Marking for Shipment (Civil Agencies)

    Military Standards

    MIL-STD-129 Marking for Shipment and Storage


    ICS Code

    ICS Number Code 77.140.50 (Flat steel products and semi-products)

    UNSPSC Code

    UNSPSC Code 30264100(Steel alloy sheets); 30264000(Carbon steel sheets)


    DOI: 10.1520/A0635_A0635M-00

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top