1. Scope
1.1 This specification covers a group of requirements which, with the exceptions of Section 4.3, Section 12, Section 19, and Section 20, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification specifies different requirements, in which case the requirement of the product specification shall prevail.
1.2 Sections 4.3 or 19 are mandatory if the product specification has a requirement for product analysis or flattening tests.
1.3 Section 20 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters.
1.4 Section 12 is for information only.
1.5 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification, only the requirement of the product specification need be satisfied.
| Title of Specification | ASTM DesignationA |
|
| Seamless Carbon Steel Pipe for High-Temperature Service | A106 |
| Seamless and Welded Austenitic Stainless Steel Pipe | A312/A312M |
| Seamless and Welded Steel Pipe for Low-Temperature Service | A333/A333M |
| Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service | A335/A335M |
| Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature Service | A358/A358M |
| Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service | A369/A369M |
| Seamless Austenitic Steel Pipe for Use With High-Temperature Central-Station Service | A376/A376M |
| Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission Systems | A381 |
| Seamless Ferritic Alloy-Steel Pipe Specially Heat Treated for High-Temperature Service | A405 |
| Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature Service | A409/A409M |
| Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature Service | A426 |
| Austenitic Steel Forged and Bored Pipe for High-Temperature Service | A430/A430M |
| Centrifugally Cast Austenitic Steel Pipe for High-Temperature Service | A451 |
| Centrifugally Cast Austenitic Steel Cold-Wrought Pipe for High-Temperature Service | A452 |
| Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures | A524 |
| Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperatures | A608 |
| Centrifugally Cast Carbon Steel Pipe for High-Temperature Service | A660 |
| Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures | A671 |
| Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures | A672 |
| Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures | A691 |
| Seamless, Welded Ferritic, and Martensitic Stainless Steel Pipe | A731/A731M |
| Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe | A790/A790M |
| Single- or Double-Welded Austenitic Stainless Steel Pipe | A813/A813M |
| Cold-Worked Welded Austenitic Stainless Steel Pipe | A814/A814M |
| Centrifugally Cast Ferritic/Austenitic Stainless Steel Pipe for Corrosive Environments | A872 |
AThese designations refer to the latest issue of the respective specifications.1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation (SI) of the product specification is specified in the order.
Note 1--The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size."
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A450/A450M Specification for General Requirements for Carbon and Low Alloy Steel Tubes
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
D3951 Practice for Commercial Packaging
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ANSI Standards
B36.19 Stainless Steel Pipe
Military Standards
MIL-STD-792 Identification Marking Requirements for Special Purpose Components
Federal Standards
Fed.Std.No.183 Continuous Identification Marking of Iron and Steel Products
Steel Structures Painting Council
SSPC-SP6 Surface Preparation Specification No. 6 Commercial Blast Cleaning
Keywords
alloy steel pipe; carbon steel pipe; general delivery requirements; steel pipe;
ICS Code
ICS Number Code 23.040.10 (Iron and steel pipes)
DOI: 10.1520/A0530_A0530M-99E01
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
