ASTM A510/A510M-11

    Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel


      Format Pages Price  
    PDF 6 $51.60   ADD TO CART


    1. Scope

    1.1 This specification covers general requirements for carbon and alloy steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths.

    1.2 In case of conflict, the requirements in the purchase order, on the drawing, in the individual specification, and in this general specification shall prevail in the sequence named.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    ^REFERENCE:

    ASTM Standards:

    A5 Specification for High-Carbon Steel Joint Bars; Replaced by A 3 (Withdrawn)

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A510M Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel (Metric)

    A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A1040 Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E30 Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron, and Wrought Iron (Withdrawn)

    E112 Test Methods for Determining Average Grain Size

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    SAE Standard:

    J 1086 Numbering Metals and Alloy

    AIAG Standard:

    AIAGB-5 02.00 Primary Metals Identification Tag Application Standard


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A5 Specification for High-Carbon Steel Joint Bars; Replaced by A 3

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A510M Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel (Metric)

    A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A1040 Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E30 Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron, and Wrought Iron

    E112 Test Methods for Determining Average Grain Size

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    SAE Standard

    J 1086 Numbering Metals and Alloy

    AIAG Standard

    AIAGB-5 02.00 Primary Metals Identification Tag Application Standard


    ICS Code

    ICS Number Code 77.140.65 (Steel wire, wir ropes and link chains)

    UNSPSC Code

    UNSPSC Code 31152200(Non electric iron and steel wire)


    Referencing This Standard

    DOI: 10.1520/A0510-11

    ASTM International is a member of CrossRef.


    Citation Format

    ASTM A510 / A510M-11, Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel, ASTM International, West Conshohocken, PA, 2011, www.astm.org

    Back to Top