ASTM A354-04e1

    Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners


      Format Pages Price  
    PDF 7 $51.60   ADD TO CART


    1. Scope

    1.1 This specification covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4 in. and under in diameter for application at normal atmospheric temperatures, where high strength is required and for limited application at elevated temperature (Note 0). Any alloy steel capable of meeting the minimum mechanical and chemical properties set forth in this specification may be used. Note 1 - For bolts, studs, or other externally threaded fasteners, to be used at elevated temperatures, refer to Specification A 193/A 193M.

    1.2 Two levels of bolting strength are covered, designated Grades BC and BD. Selection will depend upon design and the stresses and service for which the product is to be used. Note 2 - Quenched and tempered alloy steel bolts for structural steel joints up through 11/2 in. in diameter are covered in Specification A 490. Alloy steel bolts, studs, and other externally threaded fasteners (that is, heavy hex-structural bolts over 11/2 in., hex bolts, anchor bolts, and countersunk bolts) exhibiting similar mechanical properties to bolts conforming to Specification A 490 shall be covered by Grade BD of this specification.

    When bolts of Grade BD of this specification are considered for pretentioned applications in excess of 50 % of the bolt tensile strength, the additional requirements of head size, maximum tensile strength, nut size and strength, washer hardness, tests, and inspections contained in Specification A 490 should be carefully considered.

    1.3 Nuts are covered in Specification A 563. Unless otherwise specified, the grade and style of nut for each grade of fastener shall be as follows:

    Nuts of other grades and styles having specified proof load stresses (Specification A 563, Table 3) greater than the specified grade and style of nut are suitable.

    Grade of Fastener and Surface FinishNut Grade and Style
    BC, plain (or with a coating of insufficient thick-ness to require over-tapped nuts) C, heavy hex
    BC, zinc-coated (or with a coating thickness re-quiring over-tapped nuts) DH, heavy hex
    BD, all finishes DH, heavy hex

    1.4 The values stated in inch-pound units are to be regarded as the standard.

    1.5 Terms used in this specification are defined in Terminology F 1789 unless otherwise defined herein.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A193/A193M Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

    A490 Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

    A563 Specification for Carbon and Alloy Steel Nuts

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    D3951 Practice for Commercial Packaging

    F436 Specification for Hardened Steel Washers

    F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1789 Terminology for F16 Mechanical Fasteners

    F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners


    ICS Code

    ICS Number Code 21.060.10 (Bolts, screws, studs)

    UNSPSC Code

    UNSPSC Code 31161600(Bolts); 31163300(Studs)


    Referencing This Standard

    DOI: 10.1520/A0354-04E01

    ASTM International is a member of CrossRef.


    Citation Format

    ASTM A354-04e1, Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners, ASTM International, West Conshohocken, PA, 2004, www.astm.org

    Back to Top