ASTM A325M-07

    Historical Standard: ASTM A325M-07 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]

    SUPERSEDED (see Active link, below)


    Buy Standard (PDF)
    7 pages
    $50.40

    Active (view current version of standard)


    ASTM A325M

    1. Scope

    1.1 This specification covers two types of quenched and tempered, steel, metric heavy hex structural bolts having a minimum tensile strength of 830 MPa (Note 1).

    1.2 The bolts are intended for use in structural connections. These connections are comparable to those covered under the requirements of the Specification for Structural Joints using ASTM A 325 or A 490 bolts, approved by the Research Council on Structural Connections; endorsed by the American Institute of Steel Construction and by the Industrial Fastener Institute.

    1.3 The bolts are furnished in sizes M12 to M36 inclusive. They are designated by type denoting chemical composition as follows:

    1.3.1 Type 1Medium-carbon, carbon boron, medium carbon alloy, or alloy boron steel.

    1.3.2 Type 2Withdrawn in 2003.

    1.3.3 Type 3Weathering Steel.

    1.4 This specification is applicable to metric heavy hex, structural bolts only.

    1.5 Terms used in this specification are defined in Terminology F 1789.

    1.6 The following safety hazard caveat pertains only to the test methods portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1—This specification is the metric companion to the inch pound Specification A 325.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

    A490M Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)

    A563M Specification for Carbon and Alloy Steel Nuts (Metric)

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    D3951 Practice for Commercial Packaging

    F436M Specification for Hardened Steel Washers (Metric)

    F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)

    F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F959M Specification for Compressible-Washer-Type Direct Tension Indicators for Use With Structural Fasteners (Metric)

    F1136M Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners (Metric)

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1789 Terminology for F16 Mechanical Fasteners

    G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels

    ASME Standards

    B 1.13M Metric Screw Threads

    B 18.18.3M Inspection and Quality Assurance for Special Purpose Fasteners

    B 18.2.3.7M Metric Heavy Hex Structural Bolts

    B 18.24 Part Identifying Number (PIN) Code System Standard for B18 Fastener Products

    RCSC Standard

    SpecificationforStru


    ICS Code

    ICS Number Code 21.060.10 (Bolts, screws, studs)

    UNSPSC Code

    UNSPSC Code 31161614(Structural bolts )


    DOI: 10.1520/A0325M-07

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top