ASTM A312/A312M-01a

    Historical Standard: ASTM A312/A312M-01a Standard Specification for Seamless and Welded Austenitic Stainless Steel Pipes

    SUPERSEDED (see Active link, below)


    Buy Standard (PDF)
    10 pages
    $50.40

    Active (view current version of standard)


    ASTM A312 / A312M

    1. Scope

    1.1 This specification covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service.

    Note 1—When the impact test criterion for a low-temperature service would be 15 ft-lbf [20 J] energy absorption or 15 mils [0.38 mm] lateral expansion, some of the austenitic stainless steel grades covered by this specification are accepted by certain pressure vessel or piping codes without the necessity of making the actual test. For example, Grades TP304, TP304L, and TP347 are accepted by the ASME Pressure Vessel Code, Section VIII Division 1, and by the Chemical Plant and Refinery Piping Code, ANSI B31.3, for service at temperatures as low as -425oF [-250oC] without qualification by impact tests. Other AISI stainless steel grades are usually accepted for service temperatures as low as -325oF [-200oC] without impact testing. Impact testing may, under certain circumstances, be required. For example, materials with chromium or nickel content outside the AISI ranges, and for material with carbon content exceeding 0.10 %, are required to be impact tested under the rules of ASME Section VIII Division 1 when service temperatures are lower than -50oF [-45oC].

    1.2 Grades TP304H, TP309H, TP309HCb, TP310H, TP310HCb, TP316H, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP309Cb, TP309S, TP310Cb, TP310S, TP316, TP321, TP347, and TP348, and are intended for high-temperature service.

    1.3 Optional supplementary requirements are provided for pipe where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, one or more of these may be specified in the order.

    1.4 Table X1.1 lists the standardized dimensions of welded and seamless stainless steel pipe as shown in ANSI B36.19. These dimensions are also applicable to heavily cold worked pipe. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification.

    1.5 Grades TP321 and TP321H have lower strength requirements for pipe manufactured by the seamless process in nominal wall thicknesses greater than 3/8 in. [9.5 mm].

    1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.

    Note 2—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size."

    <>


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASME Standard

    ASMEBoilerandPressur : Section VIII Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Two Park Ave., New York, NY 10016-5990, http://www.asme.org.

    AWS Standard

    A5.9 Corrosion-Resisting Chromium and Chromium-Nickel Steel Welding Rods and Electrodes Available from American Welding Society (AWS), 550 NW LeJeune Rd., Miami, FL 33126, http://www.aws.org.

    Other Standard

    SAEJ1086 Practice for Numbering Metals and Alloys (UNS) Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.

    ASTM Standards

    A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe

    A1016/A1016M Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes

    E112 Test Methods for Determining Average Grain Size

    E381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    ANSI Standards

    B1.20.1 Pipe Threads, General Purpose

    B36.10 Welded and Seamless Wrought Steel Pipe

    B36.19 Stainless Steel Pipe


    ICS Code

    ICS Number Code 23.040.10 (Iron and steel pipes)

    UNSPSC Code

    UNSPSC Code 40171621(Industrial welded stainless steel pipe); 40171622(Industrial seamless stainless steel pipe)


    DOI: 10.1520/A0312_A0312M-01A

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top