ASTM A109/A109M-00e1

    Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF 9 $50.40   ADD TO CART


    1. Scope

    1.1 This specification covers cold-rolled carbon steel strip in cut lengths or coils, furnished to closer tolerances than cold-rolled carbon steel sheet, with specific temper, with specific edge or specific finish, and in sizes as follows:

    Width, in. Thickness, in.
    Over 1/2 to 23 15/16 0.300 and under
    Over 12.5 to 600 mm7.6 mm and under

    1.2 Cold-rolled strip is produced with a maximum specified carbon not exceeding 0.25 percent.

    1.3 Strip tolerance products may be available in widths wider than 23 15/16 in. [600 mm] by agreement between purchaser and supplier. However, such products are technically classified as cold rolled sheet. This specification does not include cold-rolled carbon spring steel, Specification A 682/682M. The tolerances, finishes, tempers, edges, and available widths and thicknesses differentiate cold rolled strip from the product known as cold rolled sheet which is defined by Specification A568/A568M and Specification A682/A682M.

    1.4 For the purpose of determining conformance with this specification, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.

    1.5 The SI portions of the tables contained herein list permissible variations in dimensions and mass (see Note 1) in SI (metric) units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the "M" specification is used.

    Note 1--the term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass.

    1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems will result in nonconformance with the specification.

    1.7 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

    A682/A682M Specification for Steel, Strip, High-Carbon, Cold-Rolled, General Requirements For

    A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    E8 Test Methods for Tension Testing of Metallic Materials

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E430 Test Methods for Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://quicksearch.dla.mil/

    Federal Standard

    123 Marking for Shipments (Civil Agencies)

    183 Continuous Identification Marking of Iron and Steel Products


    ICS Code

    ICS Number Code 77.140.50 (Flat steel products and semi-products)

    UNSPSC Code

    UNSPSC Code 30264400(Carbon steel ingots strips billets and coil)


    DOI: 10.1520/A0109_A0109M-00E01

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top