ASTM A1035/A1035M-13

    Standard Specification for Deformed and Plain, Low-carbon, Chromium, Steel Bars for Concrete Reinforcement

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF 6 $51.60   ADD TO CART


    1. Scope

    1.1 This specification covers low-carbon, chromium, steel bars, deformed and plain for concrete reinforcement in cut lengths and coils. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1. The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.2

    TABLE 1 Deformed Bar Designation Numbers, Nominal Weights [Masses], Nominal Dimensions, and Deformation Requirements

    Bar Designation
    No.

    Nominal Weight, lb/ft
    [Nominal Mass, kg/m]

    Nominal DimensionsA

    Deformation Requirements, in. [mm]

    Diameter,
    in. [mm]

    Cross-Sectional
    Area,
    in. 2 [mm2]

    Perimeter
    in. [mm]

    Maximum
    Average
    Spacing

    Minimum
    Average
    Height

    Maximum Gap
    (Chord of 12.5 % of
    Nominal Perimeter)

     3 [10]

     0.376 [ 0.560]

    0.375 [ 9.5]

    0.11 [  71]

    1.178 [ 29.9]

    0.262  [ 6.7]

    0.015 [0.38]

    0.143 [ 3.6]

     4 [13]

     0.668 [ 0.994]

    0.500 [12.7]

    0.20 [ 129]

    1.571 [ 39.9]

    0.350  [ 8.9]

    0.020 [0.51]

    0.191 [ 4.9]

     5 [16]

     1.043 [ 1.552]

    0.625 [15.9]

    0.31 [ 199]

    1.963 [ 49.9]

    0.437 [11.1]

    0.028 [0.71]

    0.239 [ 6.1]

     6 [19]

     1.502 [ 2.235]

    0.750 [19.1]

    0.44 [ 284]

    2.356 [ 59.8]

    0.525 [13.3]

    0.038 [0.97]

    0.286 [ 7.3]

     7 [22]

     2.044 [ 3.042]

    0.875 [22.2]

    0.60 [ 387]

    2.749 [ 69.8]

    0.612 [15.5]

    0.044 [1.12]

    0.334 [ 8.5]

     8 [25]

     2.670 [ 3.973]

    1.000 [25.4]

    0.79 [ 510]

    3.142 [ 79.8]

    0.700 [17.8]

    0.050 [1.27]

    0.383 [ 9.7]

     9 [29]

     3.400 [ 5.060]

    1.128 [28.7]

    1.00 [ 645]

    3.544 [ 90.0]

    0.790 [20.1]

    0.056 [1.42]

    0.431 [10.9]

    10 [32]

     4.303 [ 6.404]

    1.270 [32.3]

    1.27 [ 819]

    3.990 [101.3]

    0.889 [22.6]

    0.064 [1.63]

    0.487 [12.4]

    11 [36]

     5.313 [ 7.907]

    1.410 [35.8]

    1.56 [1006]

    4.430 [112.5]

    0.987 [25.1]

    0.071 [1.80]

    0.540 [13.7]

    14 [43]

     7.65  [11.38 ]

    1.693 [43.0]

    2.25 [1452]

    5.32  [135.1]

    1.185 [30.1]

    0.085 [2.16]

    0.648 [16.5]

    18 [57]

    13.60  [20.24 ]

    2.257 [57.3]

    4.00 [2581]

    7.09  [180.1]

    1.58  [40.1]

    0.102 [2.59]

    0.864 [21.9]

    A The nominal dimensions of a deformed bar are equivalent to those of a plain round bar having the same weight [mass] per foot [metre] as the deformed bar.

    1.2 Bars are of two minimum yield strength levels as defined in 9.2: namely, 100 000 psi [690 MPa], and 120 000 [830 MPa] designated as Grade 100 [690] and Grade 120 [830], respectively.

    Note 1Caution: Designers need to be aware that typical design standards limit the design strength to 80 000 psi [550 MPa], except for prestressing steel and for spiral transverse reinforcement. Members reinforced with bars with yield strengths that are considerably above 80 000 psi [550 MPa] may exhibit behavior that differs from that expected of conventional reinforced concrete members or may require special detailing to ensure adequate performance at service and factored loads.

    1.3 Deformed bars shall have a minimum yield strength and other tensile properties in accordance with Table 2. Hot-rolled plain rounds in sizes up to and including 2.25 in. [57.2 mm] in diameter in coils or cut lengths when specified for dowels, spirals, structural ties or bar supports shall be furnished under this specification and shall also meet the tensile properties requirements of Table 2. Ductility properties for plain rounds shall be those of the nearest smaller nominal diameter deformed bar size in Table 2. Requirements covering deformation dimensions and marking are not applicable to plain rounds.

    TABLE 2 Tensile Properties Requirements

     

    Grade 100 [690]

    Grade 120 [830]

    Tensile strength, min, psi [MPa]

    150 000 [1030]

    150 000 [1030]

    Yield strength (0.2 % offset), min, psi [MPa]

    100 000 [ 690]

    120 000 [ 830]

    Stress corresponding to an extension under
     load of 0.0035 in./in. [0.0035 mm/mm],
     min, psi [MPa]

     80 000 [ 550]

     90 000 [ 620]

    Elongation in 8 in. [200 mm], min, %:

     

     

     Bar Designation No.

     

     

      3 through 11 [10 through 36]

    7

    7

      14, 18 [43, 57]

    6


    Note 2Welding of the material in this specification should be approached with caution since no specific provisions have been included to enhance its weldability. When this steel is to be welded, a welding procedure suitable for the chemical composition and intended use or service should be used.

    1.4 Requirements for alternate bar sizes are presented in Annex A1. The requirements in Annex A1 only apply when specified by the purchaser (see 4.1.10).

    1.5 This specification is applicable for orders in either inch-pound units (as Specification A1035) or in SI units (as Specification A1035M).

    1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A510/A510M Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel, and Alloy Steel

    A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    U.S. Military Standard

    MIL-STD-129 Marking for Shipment and Storage

    U.S. Federal Standard

    Fed. Std. No.  Marking for Shipment (Civil Agencies)


    ICS Code

    ICS Number Code 77.140.15 (Steels for reinforcement of concrete)

    UNSPSC Code

    UNSPSC Code 30103623(Reinforcing bar or rebar or mesh)


    DOI: 10.1520/A1035_A1035M

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top