ASTM A1018/A1018M-01a

    Standard Specification for Steel, Sheet and Strip, Heavy Thickness Coils, Hot Rolled, Carbon, Structural, High-Strength Low-Alloy, Columbium or Vanadium, and High-Strength Low-Alloy with Improved Formability

    SUPERSEDED (see Active link, below)

      Format Pages Price  
    PDF 5 $50.40   ADD TO CART

    1. Scope

    1.1 This specification covers hot rolled, heavy thickness coils beyond the size limits of specification A1011.

    1.2 The product is available in three designations; Structural Steel, and High-Strength Low-Alloy Steel, Columbium or Vanadium, and High-Strength Low-Alloy Steel with Improved Formability.

    1.3 This material is available only in coils described as follows:

    ProductSize Limits, Coils Only
    Width, in [mm]Thickness, in [mm]
    Strip Over 8 to 12, incl
    [Over 200 to 300]
    0.230 to 1.000, incl
    [Over 6.0 to 25]
    Sheet Over 12 to 48, incl
    [Over 300 to 1200]
    0.230 to 1.000, incl
    [Over 6.0 to 25]
    Sheet Over 48
    [Over 1200]
    0.180 to 1.000, incl
    [Over 4.5 to 25]

    1.4 Sheet and strip in coils of sizes noted in 1.3 are covered by this specification only with the following provisions:

    1.4.1 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils). Plate produced in this manner is no longer governed by this sheet steel specification and since this material is now plate, the appropriate plate standard must now apply.

    1.4.2 This specification is not applicable to the steels covered by Specification A635/A635M.

    1.4.3 The dimensional tolerances of Specification A635/A635M are applicable to material produced to this specification.

    1.4.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming.

    1.4.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations.

    1.5 The values stated in either inch-pound units or SI units [metric] are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

    A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

    A572/A572M Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel

    A635/A635M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels

    ICS Code

    ICS Number Code 77.140.20 (Steels of high quality)

    UNSPSC Code

    UNSPSC Code 30264000(Carbon steel sheets)

    DOI: 10.1520/A1018_A1018M-01A

    ASTM International is a member of CrossRef.

    Citing ASTM Standards
    Back to Top