ASTM A1003/A1003M-12

    Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members

    SUPERSEDED (see Active link, below)


      Format Pages Price  
    PDF 7 $50.40   ADD TO CART


    1. Scope

    1.1 This specification covers coated steel sheet used in the manufacture of cold-formed framing members, such as, but not limited to, studs, joists, purlins, girts, and track.

    1.2 The steel sheet used for cold-formed framing members includes metallic-coated, painted metallic-coated, or painted nonmetallic-coated.

    1.3 The values stated in either inch-pound or SI units shall be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.

    1.4 Unless the order specifies the M designation [SI units], the product shall be furnished to inch-pound units.

    1.5 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A463/A463M Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process

    A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

    A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

    A755/A755M Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products

    A792/A792M Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process

    A875/A875M Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process

    A879/A879M Specification for Steel Sheet, Zinc Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface

    A902 Terminology Relating to Metallic Coated Steel Products

    A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A1004/A1004M Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-Metallic, and Nonmetallic-Coated Steel Sheet Intended for Use as Cold Formed Framing Members

    A1046/A1046M Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process

    A1063/A1063M Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process

    D714 Test Method for Evaluating Degree of Blistering of Paints

    D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers

    D1654 Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments

    D4138 Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means

    D4145 Test Method for Coating Flexibility of Prepainted Sheet

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    ISO Standard

    ISO9223 Corrosion of Metals and Alloys--Corrosivity of Atmospheres-Classification Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.

    AISI Standard

    SpecificationfortheD


    ICS Code

    ICS Number Code 77.140.50 (Flat steel products and semi-products)

    UNSPSC Code

    UNSPSC Code 30264000(Carbon steel sheets)


    DOI: 10.1520/A1003_A1003M-12

    ASTM International is a member of CrossRef.


    Citing ASTM Standards
    Back to Top