A 478 Specification for Chromium-Nickel Stainless Steel Weaving and Knitting Wire
A 580/A 580M Specification for Stainless Steel Wire
A 653/A 653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
B 813 Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
C 67 Test Methods for Sampling and Testing Brick and Structural Clay Tile
C 128 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate
C 136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
C 289 Test Method for Potential Alkali-Silica Reactivity of Aggregates (Chemical Method)
C 311 Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete
C 593 Specification for Fly Ash and Other Pozzolans for Use with Lime
C 618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C 739 Specification for Cellulosic Fiber Loose-Fill Thermal Insulation
C 936 Specification for Solid Concrete Interlocking Paving Units
C 989 Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars
C 1240 Standard Specification for Silica Fume Used in Cementitious Mixtures
C 1386 Specification for Precast Autoclaved Aerated Concrete (PAAC) Wall Construction Units
C 1483 Specification for Exterior Solar Radiation Control Coatings on Buildings
D 198 Test Methods of Static Tests of Lumber in Structural Sizes
D 217 Test Methods for Cone Penetration of Lubricating Grease
D 696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30—C and 30—C with a Vitreous Silica Dilatometer
D 698 Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kN-m/m3))
D 1435 Practice for Outdoor Weathering of Plastics
D 1557 Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))
D 1972 Practice for Generic Marking of Plastic Products
D 2103 Specification for Polyethylene Film and Sheeting
D 3273 Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber
D 3960 Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
D 4552 Practice for Classifying Hot-Mix Recycling Agents
D 4840 Guide for Sampling Chain-of-Custody Procedures
D 4887 Practice for Preparation of Viscosity Blends for Hot Recycled Bituminous Materials
D 5033 Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics
D 5106 Specification for Steel Slag Aggregates for Bituminous Paving Mixtures
D 5116 Guide for Small-Scale Environmental Chamber Determinations of Organic Emissions from Indoor Materials/Products
D 5268 Specification for Topsoil Used for Landscaping Purposes
D 5359 Specification for Glass Cullet Recovered from Waste for Use in Manufacture of Glass Fiber
D 5505 Practice for Classifying Emulsified Recycling Agents
D 5539 Specification for Seed Starter Mix
D 5603 Classification for Rubber Compounding MaterialsùRecycled Vulcanizate Particulate Rubber
D 5663 Guide for Validating Recycled Content in Packaging Paper and Paperboard
D 5759 Guide for Characterization of Coal Fly Ash and Clean Coal Combustion Fly Ash for Potential Uses
D 5792 Practice for Generation of Environmental Data Related to Waste Management Activities: Development of Data Quality Objectives
D 5851 Guide for Planning and Implementing a Water Monitoring Program
D 5852 Test Method for Erodibility Determination of Soil in the Field or in the Laboratory by the Jet Index Method
D 6002 Guide for Assessing the Compostability of Environmentally Degradable Plastics
D 6006 Guide for Assessing Biodegradability of Hydraulic Fluids
D 6007 Test Method for Determining Formaldehyde Concentration in Air from Wood Products Using a Small Scale Chamber
D 6046 Classification of Hydraulic Fluids for Environmental Impact
D 6081 Practice for Aquatic Toxicity Testing of Lubricants: Sample Preparation and Results Interpretation
D 6108 Test Method for Compressive Properties of Plastic Lumber and Shapes
D 6109 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber
D 6112 Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes
D 6117 Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes
D 6155 Specification for Nontraditional Coarse Aggregates for Bituminous Paving Mixtures
D 6245 Guide for Using Indoor Carbon Dioxide Concentrations to Evaluate Indoor Air Quality and Ventilation
D 6261 Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
D 6262 Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)
D 6270 Practice for Use of Scrap Tires in Civil Engineering Applications
D 6330 Practice for Determination of Volatile Organic Compounds (Excluding Formaldehyde) Emissions from Wood-Based Panels Using Small Environmental Chambers Under Defined Test Conditions
D 6345 Guide for Selection of Methods for Active, Integrative Sampling of Volatile Organic Compounds in Air
D 6400 Specification for Compostable Plastics
D 6435 Test Method for Shear Properties of Plastic Lumber and Plastic Lumber Shapes
D 6629 Guide for Selection of Methods for Estimating Soil Loss by Erosion
D 6662 Specification for Polyolefin-Based Plastic Lumber Decking Boards
D 6712 Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes
E 90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
E 408 Test Methods for Total Normal Emittance of Surfaces Using Inspection-Meter Techniques
E 413 Classification for Rating Sound Insulation
E 477 Test Method for Measuring Acoustical and Airflow Performance of Duct Liner Materials and Prefabricated Silencers
E 648 Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source
E 781 Practice for Evaluating Absorptive Solar Receiver Materials When Exposed to Conditions Simulating Stagnation in Solar Collectors with Cover Plates
E 782 Practice for Exposure of Cover Materials for Solar Collectors to Natural Weathering Under Conditions Simulating Operational Mode
E 823 Practice for Nonoperational Exposure and Inspection of a Solar Collector
E 881 Practice for Exposure of Solar Collector Cover Materials to Natural Weathering Under Conditions Simulating Stagnation Mode
E 903 Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres
E 917 Practice for Measuring Life-Cycle Costs of Buildings and Building Systems
E 948 Test Method for Electrical Performance of Photovoltaic Cells Using Reference Cells Under Simulated Sunlight
E 971 Practice for Calculation of Photometric Transmittance and Reflectance of Materials to Solar Radiation
E 1021 Test Methods for Measuring Spectral Response of Photovoltaic Cells
E 1038 Test Method for Determining Resistance of Photovoltaic Modules to Hail by Impact with Propelled Ice Balls
E 1040 Specification for Physical Characteristics of Nonconcentrator Terrestrial Photovoltaic Reference Cells
E 1171 Test Method for Photovoltaic Modules in Cyclic Temperature and Humidity Environments
E 1333 Test Method for Determining Formaldehyde Concentrations in Air and Emission Rates from Wood Products Using a Large Chamber
E 1362 Test Method for Calibration of Non-Concentrator Photovoltaic Secondary Reference Cells
E 1423 Practice for Determining the Steady State Thermal Transmittance of Fenestration Systems
E 1433 Guide for Selection of Standards on Environmental Acoustics
E 1462 Test Methods for Insulation Integrity and Ground Path Continuity of Photovoltaic Modules
E 1596 Test Methods for Solar Radiation Weathering of Photovoltaic Modules
E 1597 Test Method for Saltwater Pressure Immersion and Temperature Testing of Photovoltaic Modules for Marine Environments
E 1609 Guide for Development and Implementation of a Pollution Prevention Program
E 1686 Guide for Selection of Environmental Noise Measurements and Criteria
E 1690 Test Method for Determination of Ethanol Extractives in Biomass
E 1721 Test Method for Determination of Acid-Insoluble Residue in Biomass
E 1755 Test Method for Ash in Biomass
E 1758 Test Method for Determination of Carbohydrates in Biomass by High Performance Liquid Chromatography
E 1780 Guide for Measuring Outdoor Sound Received from a Nearby Fixed Source
E 1799 Practice for Visual Inspections of Photovoltaic Modules
E 1802 Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules
E 1821 Test Method for Determination of Carbohydrates in Biomass by Gas Chromatography
E 1830 Test Methods for Determining Mechanical Integrity of Photovoltaic Modules
E 1971 Guide for Stewardship for the Cleaning of Commercial and Institutional Buildings
E 1983 Guide for Assessment of Wetland Functions
E 1991 Guide for Environmental Life Cycle Assessment of Building Materials/Products
E 2047 Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays
E 2114 Terminology for Sustainability Relative to the Performance of Buildings
E 2129 Practice for Data Collection for Sustainability Assessment of Building Products
F 2034 Specification for Sheet Linoleum Floor Covering
G 40 Terminology Relating to Wear and Erosion